A pin lock keg is a type of beer keg that uses a pin instead of a standard tap to dispense the beer. Pin lock kegs are often used by homebrewers and small breweries because they are less expensive than thir ball lock counterparts. Pin lock kegs have two posts on the top, each with a different diameter. One post is for the gas (usually CO2) and the other is for the beer. A pin is inserted into each post to seal the keg. To dispense the beer, the gas pin is removed and replaced with a tap. The beer can then be dispensed by pressing down on the tap.
What's The Difference Between PIN Lock And Ball Lock Kegs?
The main difference between PIN lock and ball lock kegs is that ball lock kegs use a ring of ball bearings to secure gas and liquid connections to the keg, while pin lock kegs use pins on the keg fittings to secure the gas and liquid line fittings to the kegs (two pins for gas-in, three pins for liquid-out).
Can You Convert A Pin Lock Keg To Ball Lock?
Yes, it is possible to convert a pin lock keg to Ball Lock. You will need to unscrew the pin lock posts and screw on the ball lock posts. The conversion kit allows you to keep using your existing Firestone, Spartanburg or Hoover pin lock keg with a new ball lock keg.
Are Ball Lock And Pin Lock Posts Interchangeable?
Yes, ball lock and pin lock posts are interchangeable. Both types of posts have the same dimensions, so they can be swapped out as needed. Ball lock posts are typically used for holding kegs in place, while pin lock posts are often used for holding Cornelius (soda) barrels in place.
What Are The Two Types Of Kegs?
The two types of kegs are pin lock kegs and ball lock kegs. Pin lock kegs have a pin on the side that is used to connect the gas and liquid lines. Ball lock kegs have a ball on the top that is used to connect the gas and liquid lines.
What Is A Pepsi Style Keg?
A Pepsi style keg is a type of keg that uses ball lock disconnects to connect and disconnect the gas and liquid lines. Ball lock disconnects lock on with a twist of the collar.
What Is A Sanke Keg?
A Sanke Keg is a type of beer keg that has a single valve on the top of it. This valve allows both beer and gas to pass through. The beer flows via a spear in the valve that runs to the bottom of the Sanke keg.
What Are The Different Types Of Kegs?
Ball lock kegs have a ball bearing that locks into place to keep the pressure in. Pin lock kegs have a pin that locks into place. Sankey kegs are used by commercial breweries and have a dfferent locking mechanism.
How Do Ball Locks Work?
Ball locks are a type of locking mechanism that uses balls to secure two plates together. The balls are housed inside the shank of the lock and are activated by a setscrew in the head of the shank. Turning the setscrew pushes a fourth ball into a tapered groove in the receiver bushing, whih draws the plates together and secures them in place.
What Is A Keg Wrench For?
A keg wrench is a tool that is used to loosen or tighten the faucet on a shank or draft tower. This is an essential tool for draft system maintenance and repair.
What Are Keg Sizes?
A keg is a cylindrical container that is used to store and transport liquids, typically beer. There are various keg sizes available, which vary in capacity. The most common keg size is the half barrel, which has a capacity of 15.5 gallons, or 124 pints. Other keg sizes include the pony keg (7.75 gallons), the sixtel (5.2 gallons), and the 50 liter (13.2 gallons).
What Is The Most Common Keg Coupler?
The D-type keg coupler, also knon as the American Sankey coupler, is the most common type of keg coupler used in North America. This type of coupler is used by the majority of North American breweries, including Molson, Corona, Coors, Budweiser, Miller, PBR, and Yuengling. The D-type keg coupler is a simple device that consists of a plug that is inserted into the top of the keg and a handle that is used to operate the valve.
How Long Does A Keg Last Once Tapped?
A keg will only last 12-24 hours after it has been tapped and pumped with oxygen. The oxygen will cause the beer to go flat and spoil quickly if it is not consumed within that time frame.
How Long Is A Keg Good For?
Pasteurized beers can stay fresh from three to six months. For non-pasteurized beers, you can expect the keg to stay fresh approximately two months. Each beer is diffrent and storing your beer at the ideal temperature is essential for its preservation.
What Is A Ball Lock Pin?
A ball lock pin is a type of quick release pin that uses a series of balls to secure it in place. The balls are held in place by a spring-loaded sleeve, and when the sleeve is pushed back, the balls are released and the pin can be removed. Ball lock pins are used in a variety of applications were quick release and secure locking is required, such as in machinery and equipment mounting.
What Is A 5 Gallon Keg Called?
A 5 gallon keg is called a Cornelius keg. This keg is now commonly used by homebrewers as an alternative to bottling beer because this keg size is the typical size of a homebrew batch, 5 gallons.
How Do You Keep A Keg From Sticking To The Tap?
If you are having difficulty keeping your keg from sticking to the tap, there are a few things that you can do. First, make sure that you are attaching the tap to the keg correctly. The tap should be inserted all the way into the keg until it is tight. If the tap is not inserted correctly, it will not seal properly and beer will leak out. Second, clean the keg before you use it. You can do this by rinsing it out with water and then sanitizing it with a solution of water and bleach. Finally, make sure that you are using fresh beer. Old beer can bcome stale and cause the keg to stick to the tap.
How Do You Keep A Keg Cold?
The cheapest way to keep a keg cold is by placing it in a suitable container and covering it with ice. Place the keg in the tub, surround it with ice and then top up with cold water. You can then eithr connect a pressure regulator and beer lines or fit a picnic tap directly to the keg.
